simsaladimbamba
May 5, 07:54 PM
Have you tried an SMC reset yet? It sometimes helped me.
Intel-based Macs: Resetting the System Management Controller (SMC) (http://support.apple.com/kb/HT3964)
Btw, the images don't show up yet.
How to attach an image to your MR post. (http://forums.macrumors.com/showthread.php?p=11836587#post11836587)
Intel-based Macs: Resetting the System Management Controller (SMC) (http://support.apple.com/kb/HT3964)
Btw, the images don't show up yet.
How to attach an image to your MR post. (http://forums.macrumors.com/showthread.php?p=11836587#post11836587)
hsaybasili
Dec 29, 01:02 PM
There must be a config file by which refresh rate is adustable. I am going to try to find it out. (yes I just have an ibook :( , but I am a very curious person:) )
In linux it is /etc/X11/xorg.conf (was /etc/X11/XF86Config) in which you can set all the display properties including refresh rates. As OS X is based on UNIX, there must be a config file to edit manually. Or let say I hope :)
Trying with a Linux live cd (for power pc architecture of course) may give some ideas. There are a lot of distributions: Ubuntu and Yellow Dog for example... If it works in linux without lines, then this is a software problem. If the lines exists, you can (I am not very sure but worth to try) also change the xorg.conf even if this is a live cd version. You can edit these files and restart Xserver afterwards.
If it is a software problem (which I also suspect), it should be possible to make it disappear by installing linux and tweeking the video settings. It may also be a firmware issue, and it won't be fixed until Apple address the problem.
So, has anyone tried the new PB with Linux??
Personally I don't see it as a problem. I have to get as close as 15cm from the screen to actually see the effect. I know that would give me a headache, lines or not :)
In linux it is /etc/X11/xorg.conf (was /etc/X11/XF86Config) in which you can set all the display properties including refresh rates. As OS X is based on UNIX, there must be a config file to edit manually. Or let say I hope :)
Trying with a Linux live cd (for power pc architecture of course) may give some ideas. There are a lot of distributions: Ubuntu and Yellow Dog for example... If it works in linux without lines, then this is a software problem. If the lines exists, you can (I am not very sure but worth to try) also change the xorg.conf even if this is a live cd version. You can edit these files and restart Xserver afterwards.
If it is a software problem (which I also suspect), it should be possible to make it disappear by installing linux and tweeking the video settings. It may also be a firmware issue, and it won't be fixed until Apple address the problem.
So, has anyone tried the new PB with Linux??
Personally I don't see it as a problem. I have to get as close as 15cm from the screen to actually see the effect. I know that would give me a headache, lines or not :)
kuwisdelu
Apr 15, 12:58 PM
> if (any(socscore<=3)) q<-0 else q=1
> q
[1] 0
Why am I only getting 1 answer?
Thanks in advance,
Ernie
One of the hardest things to remember when using R compared to other programming languages, is that almost everything you do is a vector operation. When you do q <- 0, R is going to apply the "<- 0" to the entire vector of q. And if you haven't created q before this, q will just be set equal to either 0 or 1. What you're asking R to do is if any value in socscore is less or equal to than 3, assign 0 to q, otherwise assign 1 to q. I'm assuming you want q to be a vector of 0's and 1's corresponding to whether socscore <= 3 or not?
There are a couple ways to do that. You can either use a loop:
q <- rep(NA, length(socscore))
for ( i in 1:length(socscore) {
Paris Hilton, Cameron Diaz
more...
Hale Bob Burnout Tunic
When Will Cameron Diaz Be
more...
Cameron Diaz pauses for
Hale Bob Metallic Short Sleeve
more...
in the new Cameron Diaz,
Cameron Diaz and Ashley Olsen
more...
2011-hairstyles-long-ob-
Cameron Diaz: “Lots of
more...
Gwyneth Paltrow, Cameron Diaz,
Cameron Diaz, Zac Efron,
more...
Cameron Diaz and Robert
Cameron Diaz. Credit: ROBERT
more...
Funny girl Cameron Diaz went
Hale Bob Metallic Short Sleeve
and Cameron Diaz are known
> q
[1] 0
Why am I only getting 1 answer?
Thanks in advance,
Ernie
One of the hardest things to remember when using R compared to other programming languages, is that almost everything you do is a vector operation. When you do q <- 0, R is going to apply the "<- 0" to the entire vector of q. And if you haven't created q before this, q will just be set equal to either 0 or 1. What you're asking R to do is if any value in socscore is less or equal to than 3, assign 0 to q, otherwise assign 1 to q. I'm assuming you want q to be a vector of 0's and 1's corresponding to whether socscore <= 3 or not?
There are a couple ways to do that. You can either use a loop:
q <- rep(NA, length(socscore))
for ( i in 1:length(socscore) {
MythicFrost
May 6, 12:29 AM
I'll have to check into Pro Tools, including whether I can transfer my Windows license to Mac, which I doubt - so I may end up going with Logic.
Excellent suggestion on the RAM - that must mean it has 4 slots, need to install in pairs and I don't waste what ships with the machine? And the i7 sounds like a good choice too.
Thanks for the advice!
No worries :)
That's right. It has four slots and it does need to be installed in pairs. 2x2GB and 2x4GB should work great. I've got 12GB in my 09 27" iMac.
If you're unable to transfer the license, you could just buy a copy of Windows 7 Home Premium 64-bit and install it on a partition (Which you would create with BootCamp Assistant). Then you can boot into OS X or into Windows 7 (for Pro Tools).
Excellent suggestion on the RAM - that must mean it has 4 slots, need to install in pairs and I don't waste what ships with the machine? And the i7 sounds like a good choice too.
Thanks for the advice!
No worries :)
That's right. It has four slots and it does need to be installed in pairs. 2x2GB and 2x4GB should work great. I've got 12GB in my 09 27" iMac.
If you're unable to transfer the license, you could just buy a copy of Windows 7 Home Premium 64-bit and install it on a partition (Which you would create with BootCamp Assistant). Then you can boot into OS X or into Windows 7 (for Pro Tools).
more...
iCeQuBe
Oct 26, 05:37 PM
I am at westfarms and all I can say is wow! The line is huge! Must be 200 people
jmufellow
Sep 29, 01:14 AM
Basically, I want to get an ibook, either refurb or used--just something cheap that will do internet (wireless), word processing, and that's about it. I have a biggger mac for storing music burning dvd's etc.
There's a nice ibook on the refurb page right now. My question: if I let this one pass will something else come up on that page pretty soon or is it a rare thing to find this kind of deal.
My reason for not buying now is because I did not plan to get something this soon, and money would be a tad bit tight to spring and get it right now. Should I spring for it now (aka credit card) or is it safe to wait for this deal to surface again? :confused:
Thanks for the reply BTW :)
There's a nice ibook on the refurb page right now. My question: if I let this one pass will something else come up on that page pretty soon or is it a rare thing to find this kind of deal.
My reason for not buying now is because I did not plan to get something this soon, and money would be a tad bit tight to spring and get it right now. Should I spring for it now (aka credit card) or is it safe to wait for this deal to surface again? :confused:
Thanks for the reply BTW :)
more...
sleepykidd
Apr 23, 07:35 AM
Maybe the disk image you created is corrupt?
It could be as simple as that? There isn't anything that stands out as a concrete reason why it wouldn't work?
Should I try upgrading to leopard first and then Snow Leopard? I don't have the "upgrade disc" I have the full install one that came with my other Mac.
It could be as simple as that? There isn't anything that stands out as a concrete reason why it wouldn't work?
Should I try upgrading to leopard first and then Snow Leopard? I don't have the "upgrade disc" I have the full install one that came with my other Mac.
cfairbank
Mar 3, 08:58 AM
Thinking about it. Been holding out on getting the iPad and I am ready to pull the trigger and pick one up.
more...
Bluemeanie1976
Apr 13, 10:59 AM
What file are you trying to download? Do you have a link. I can Dow oaf to airsharing, or file browser. Do you have a file handling app at all?
DrakkenWar
Apr 12, 01:11 AM
I would have to agree with a few that have posted here. There seems to be a mind set in some of the mac community that you have to upgrade! You need to have the newest shiny mac! And frankly I really don't get it. As I am typing this on my G3/800/10.4/768 iBook that bloody well does everything I need it to do on a daily basis. I have a dual G4 and dual G5 in the home office, but I really don't have the time to be in there with my daily computer needs. So if what you have does what you need? Video card issue? Meh. I have had 2 G3/900 iBooks pouch out on me with video issues, but let me tell ya, they where a hell of a lot cheaper to replace and do what I wanted them to do, than the newest mac on the block. And with that I will put away my soap box and continue using this aging beast on a a daily basis. ;)
more...
IJ Reilly
Dec 28, 03:45 PM
Reinstalling the OS even once is so unnecessary, it's difficult to conceive of reinstalling it so many times that your hard drive would be damaged.
chown33
Apr 10, 12:27 PM
Post the exact error message. An "invalid selector" error usually shows the exact selector expected.
more...
Icaras
May 5, 12:42 AM
Planning on ordering a new 2011 iMac with a 256GB SSD and 2TB drive.
Current 2010 iMac hard drive has one drive with about 375GB.
In previous migrations - it was as simple as booting the source Mac with the "T" and allowing the transfer via Firewire.
The full image will not fit on the 256GB SSD. I know I can manually move user files to an external drive and reduce the image for a full copy and then move that data to the HD on the new iMac.
Any better suggestions?
Good question and thread. I'm in the same situation...I have roughly 400GB on my current drive and am planning to move to the dual hard drive setup as well....I was originally thinking of restoring from my Time Machine, but deselecting my Music folder, as thats where basically most of my space goes to, then manually dragging that from Time Machine onto the 1 or 2 TB HD.
This is the best I can think of at the moment. I'd love to hear other ideas though too.
Current 2010 iMac hard drive has one drive with about 375GB.
In previous migrations - it was as simple as booting the source Mac with the "T" and allowing the transfer via Firewire.
The full image will not fit on the 256GB SSD. I know I can manually move user files to an external drive and reduce the image for a full copy and then move that data to the HD on the new iMac.
Any better suggestions?
Good question and thread. I'm in the same situation...I have roughly 400GB on my current drive and am planning to move to the dual hard drive setup as well....I was originally thinking of restoring from my Time Machine, but deselecting my Music folder, as thats where basically most of my space goes to, then manually dragging that from Time Machine onto the 1 or 2 TB HD.
This is the best I can think of at the moment. I'd love to hear other ideas though too.
eyelikeart
Nov 4, 12:05 PM
who's got a crew? :eek:
I'm just a patsy...honestly... ;)
I'm just a patsy...honestly... ;)
more...
MacBytes
Oct 4, 02:50 PM
http://www.macbytes.com/images/bytessig.gif (http://www.macbytes.com)
Category: Tips and How To's
Link: How to Identify if the GeForce 8600M GT of your MacBook Pro Is Defect (http://www.macbytes.com/link.php?sid=20101004155002)
Description:: none
Posted on MacBytes.com (http://www.macbytes.com)
Approved by Mudbug
Category: Tips and How To's
Link: How to Identify if the GeForce 8600M GT of your MacBook Pro Is Defect (http://www.macbytes.com/link.php?sid=20101004155002)
Description:: none
Posted on MacBytes.com (http://www.macbytes.com)
Approved by Mudbug
Ommid
Apr 22, 01:13 PM
I too have been considering OWC but surely their RAM is just a relabel of another brand?
more...
tdhurst
Sep 28, 09:41 AM
Hi, I'm going to be ordering a 12" PB in the next couple of weeks, whether the much rumored revisions happen or not but in would be cool if they did. This will be my first Mac and I'm very excited but I have a couple of questions:
Josh
1) What do you guys think of Bluetooth mice?
In my experience with Apple's BT mouse, I have only noticed lag when I had my BT keyboard hook up as well. Macally's mouse got great reviews, so I would recommend you go for it.
2) RAM - I'm going to max out the RAM (1.25g) so is there any advantage to the RAM Apple installs on built-to-order machines that makes it worth the $400 price tag or is this just the cost of convenience?
Simply convenience here...www.18004MEMORY.com...I bought a 1gig Corsair chip for my 1.5Ghz 12" powerbook and have had absolutely ZERO problems. Just make SURE it's guaranteed to work in your machine and you should be just fine.
3) I'm going to be doing a lot of video editing work with this computer, I know it's not the ideal machine for it but it's what I can afford and it should do the job until I can buy something better.
Any sort of laptop holder is fine. I have used the iCurve and am currently using the podiumpad (only real difference between them is height, the iCurve forces you to use an external keyboard) but besides that, you are going to be just fine. Fans wouldn't help much unless they were inside the case, but I have run Halo, the Doom 3 demo, Final Cut, InDesign, etc. without any problems. Yes, the internal fan does turn on and the powerbook gets warm, but never HOT.
Josh
1) What do you guys think of Bluetooth mice?
In my experience with Apple's BT mouse, I have only noticed lag when I had my BT keyboard hook up as well. Macally's mouse got great reviews, so I would recommend you go for it.
2) RAM - I'm going to max out the RAM (1.25g) so is there any advantage to the RAM Apple installs on built-to-order machines that makes it worth the $400 price tag or is this just the cost of convenience?
Simply convenience here...www.18004MEMORY.com...I bought a 1gig Corsair chip for my 1.5Ghz 12" powerbook and have had absolutely ZERO problems. Just make SURE it's guaranteed to work in your machine and you should be just fine.
3) I'm going to be doing a lot of video editing work with this computer, I know it's not the ideal machine for it but it's what I can afford and it should do the job until I can buy something better.
Any sort of laptop holder is fine. I have used the iCurve and am currently using the podiumpad (only real difference between them is height, the iCurve forces you to use an external keyboard) but besides that, you are going to be just fine. Fans wouldn't help much unless they were inside the case, but I have run Halo, the Doom 3 demo, Final Cut, InDesign, etc. without any problems. Yes, the internal fan does turn on and the powerbook gets warm, but never HOT.
Wildy
Mar 26, 05:23 AM
That's ideal, thanks a lot.
Potatochobit
Apr 3, 06:00 PM
Do you know if the external harddrive was formatted to NTFS?
what you need to do is move all the files to a PC, then reformat the external drive to FAT (best to do it with the mac)
then you can move your files back from the PC to the external hard drive and your MAC should be able to see them.
*note, if you have old fonts you need to move you should ZIP everything first on the PC
what you need to do is move all the files to a PC, then reformat the external drive to FAT (best to do it with the mac)
then you can move your files back from the PC to the external hard drive and your MAC should be able to see them.
*note, if you have old fonts you need to move you should ZIP everything first on the PC
Chrisiphone
Feb 7, 11:51 AM
my current ipod has a bunch of song on it that I ripped from cds (okay, and a few illegal downloads). However, that was two computers ago, so I'd have to re-rip the music, provided I still have it.
I can't seem to add the ripped stuff to my itunes on my current computer. I think it has something to do with copy rights, but it could also be b/c I don't know enough about macs.
Is there some way I can transfer those songs to my iTunes? I've heard that some people know how to do it.
I can't seem to add the ripped stuff to my itunes on my current computer. I think it has something to do with copy rights, but it could also be b/c I don't know enough about macs.
Is there some way I can transfer those songs to my iTunes? I've heard that some people know how to do it.
gkarris
Feb 17, 08:52 PM
http://en.wikipedia.org/wiki/Jackling_House
There you go
I remember now - saw it in a documentary about So Cal homes and Steve wanting to tear this down.
Ugly anyways and I think he did them a favor...
There you go
I remember now - saw it in a documentary about So Cal homes and Steve wanting to tear this down.
Ugly anyways and I think he did them a favor...
gekko513
Feb 15, 01:04 PM
Why can't I change icons for a file just by dragging an icon from one info window to another? It is inconsistent with how the rest of the OS X user interface works, I think.
longofest
Sep 20, 07:22 PM
That's quite a huge bug. :(
Glad they fixed it, but that kind of thing should have never been allowed to exist in the firstplace.
Glad they fixed it, but that kind of thing should have never been allowed to exist in the firstplace.
bpaluzzi
Apr 7, 02:33 PM
All l'm saying is it didn't work.
It wasn't because of that line.
It wasn't because of that line.
No comments:
Post a Comment